15895288321王总
  • 大理石如何翻新晶面及抛光养护?
  • 本站编辑:徐州爱君环保工程有限公司发布日期:2020-07-08 10:02 浏览次数:

大理石翻新晶面及抛光一般用于装饰的石材,特别是大理石经过长年累月的使用磨损或自然的风化,加至人为护理不当,很容易导致石材本身自然色泽及亮度逐渐消失;如果重新装饰的话成本太高,且时间太长,而大理石翻新工艺则是在非常短的时间内利用化学和物理的方法,在原有的基础上通过机器的研磨、抛光,使其恢复到石材原来的亮度和色泽,翻新后的亮度可达到刚刚铺设时的百分之百,既经济又省时,经翻新后的石材使用寿命在五年以上。

Marble renovation crystal face and polishing are generally used for decorative stone, especially marble after years of use wear or natural weathering, adding artificial care, it is easy to lead to the natural color and brightness of stone gradually disappear; if re decoration, the cost is too high, and the time is too long, and the marble renovation process is in a very short time to use chemical and Physical method, on the basis of the original machine grinding, polishing, to restore the original brightness and color of the stone, the brightness after renovation can reach 100% of that when it was just laid, which is economical and time-saving, and the service life of the renovated stone is more than five years.

下载.jpg

大理石翻新工艺流程

Marble renovation process

使用工具:石材翻新机、洗地机、大理石抛光机、吸尘吸水机、切割机、钻石碟片6组、红垫、白垫。

Using tools: Stone renovation machine, washing machine, marble polishing machine, dust suction machine, cutting machine, diamond disc 6 groups, red pad, white pad.

使用药剂:石材研磨剂KP92、结晶粉、云石胶、石材保护剂K2、K3或者二合一晶面液。

Chemicals used: Stone abrasive kp92, crystal powder, dolomite glue, stone protective agent K2, K3 or two in one crystal face liquid.

大理石翻新:

u=2093430529,284994029&fm=26&gp=0.jpg

Marble renovation:

a、根据大理石的缝隙情况确定是否重新开缝,若需要重新开缝,采用专用的切割机将缝隙切割均匀,然后用云石胶将其缝隙填补平整。

a. According to the gap situation of marble, determine whether to re open the seam. If it is necessary to re slit, use a special cutting machine to cut the gap evenly, and then fill the gap with dolomite glue.

b、使用专用的大理石翻新机,从50-3000号的石材水磨片由粗到细对石材进行研磨,打磨时必须遵守石材线路纹理由粗到细进行打磨,直至石材表面平滑且色泽统一,光亮平整如新。

b. Use a special marble refurbishing machine to grind the stone from the coarse to the fine from the 50-3000 stone water grinding plate. When grinding, the stone line texture must be observed from the coarse to the fine until the stone surface is smooth and uniform in color and lustre, bright and smooth as new.

0.jpg

将大理石地面保洁干净,采用石材结晶粉和结晶药剂配合晶面打磨机打磨直至干燥,在打磨机重压下让石材和结晶粉在高温作用下发生物理和化学综合反应,形成一层致密、坚硬的结晶保护层,再用专用的抛光机放上白垫和钢丝棉以“Z”字型均匀抛光,抛光后用尘推把尘埃推净即可,结晶后能增强色彩和光亮度,还能达到防滑、防水、防油等功效。

The marble floor is kept clean, and the stone crystal powder and crystallization agent are used to grind with crystal face grinder until it is dry. Under the heavy pressure of the grinder, the stone and crystal powder will react with each other under high temperature to form a dense and hard crystalline protective layer. Then the special polishing machine is used to put white pad and steel wool to polish evenly in "Z" shape, and dust is used after polishing The dust can be pushed clean. After crystallization, the color and brightness can be enhanced, and the effect of antiskid, waterproof and oil proof can be achieved.